- Place of Origin: Jiangsu, China (Mainland)
- Brand Name: MEAN WELL
- Model Number: SDR-240-24
- Output Power: 240W
- Output Type: Single
- Input Voltage: 88 ~ 264VAC
- Output Voltage: 24V
- Output Frequency: 0Hz
- Output Current: 0 ~ 10A
- Rail type:: Can be installed on DIN rail TS-35/7.5 or 15
- PFC function:: Built-in active PFC function, PF>0.93
- Protections:: Short circuit / Overload / Over voltage / Over temperature
- Industrial control equipment:: UL 508 (industrial control equipment) approved
- Industrial immunity level:: EN61000-6-2(EN50082-2) industrial immunity level
- Working temp:: -25℃ ~ +70℃
- Size:: 63*125.2*113.5mm (W*H*D)
- Certificates:: Real UL/cUL, GL, TUV, CE, CB
- MTBF:: 169.3K hrs min.
- Type:: MEAN WELL 240W 24V 10A Din Rail Power Supply SDR-240-24 with PFC
Packaging & Delivery
|Packaging Details:||Original MEAN WELL packing, 12pcs/13.4Kg/Carton
MEAN WELL 240W 24V Din Rail Power Supply SDR-240-24 with PFC
Welcome to the world of MEAN WELL!
Here is the detailed info for my original MEAN WELL 240W 24V Din Rail Power Supply SDR-240-24 with PFC. Hope you like it.
- High efficiency 91% and low power dissipation
- 150% peak load capability
- Built-in active PFC function, PF>0.93
- Protections: Short circuit / Overload / Over voltage / Over temperature
- Cooling by free air convection
- Can be installed on DIN rail TS-35/7.5 or 15
- UL 508 (industrial control equipment) approved
- EN61000-6-2(EN50082-2) industrial immunity level
- Built-in DC OK relay contact
- 100% full load burn-in test
- 3 years warranty
|RIPPLE & NOISE (max.) Note.2||100MVP-P|
|VOLTAGE ADJ. RANGE||24 ~ 28V|
|VOLTAGE TOLERANCE Note.3||±1.0%|
|SETUP.RISEHOLD.TIME Note.5||1500ms, 60ms/230VAC 3000ms, 60ms/115VAC at full load|
|HOLD UP TIME (Typ.)||20ms/230VAC 20ms/115VAC at full load|
|INPUT||VOLTAGERANGE||88 ~ 264VAC 124~ 370VDC|
|POWER FACTOR (Typ.)||0.93/230VAC 0.99/115VAC at full load|
|AC CURRENT (Typ.)||2.6A/115VAC 1.3A/230VAC|
|INRUSH CURRENT (Typ.)||33A/115VAC 65A/230VAC|
|LEAKAGE CURRENT||<1mA / 240VAC|
|PROTECTION||OVERLOAD||Normally works within 110 ~ 150% rated output power for more than 3 seconds and then shut down o/p voltage with auto-recovery|
|>150% rated power, constant current limiting with auto-recovery within 2 seconds and may cause to shut down if over 2 seconds|
|OVER TEMPERATURE||95± 5 (TSW : detect on heatsink of power switch)|
|Protection type : Shut down o/p voltage, recovers automatically after temperature goes down|
|OVER VOLTAGE||29~ 33V|
|Protection type : Shut down o/p voltage, re-power on to recover|
|FUNCTION||DC OK REALY CONTACT RATINGS (max.)||60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load|
|ENVIRONMENT||WORKING TEMP||-25~+70 (refer to output load derating curve)|
|WORKINGHUMIDITY||20~95% RH non-condensing|
|STORAGE TEMP HUMIDITY||-40~+85 10~95%RH|
|VIBRATION||Component:10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6|
|SAFETY&EMC Note 4)||SAFETY STANDARDS||UL508, TUV EN60950-1 approved|
|WITHSTAND VOLTAGE||I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC|
|ISOLATIONRESISTANCE||I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC 25 70%RH|
|EMI CONDUCTICN&||Compliance to EN55011, EN55022(CISPR22)classB|
|HARMONICCURRENT||Compliance to EN61000-3-2,-3|
|EMS IMMUNITY||Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN55024, EN61000-6-2 (EN50082-2), EN61204-3, heavy industry level,|
|criteria A, SEMI F47, GL approved|
|QTHERS||MTBF||169.3Khrs min MIL-HDBK-217F(25)|
|NOTE||1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.|
|2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.|
|3. Tolerance : includes set up tolerance, line regulation and load regulation.|
|4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.|
|5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended.|
|6. 3 seconds max., please refer to peak loading curves.|
|7. Derating may be needed under low input voltage. Please check the derating curve for more details.|
|8. After 30 minutes of burn-in.|
Storage and Packing
MEAN WELL Other Series
Why Choose Us ???
A Fast Delivery + Satisfied Customer Service Is Our NO.1 Priority!
1. Our goal is to provide you the right product and make you satisfied, All are original MEAN WELL 240W 24V Din Rail Power Supply SDR-240-24 with PFC.
2. We shall find for you the cheapest shipping term and show you the freight and shipping time. Regarding to the urgent order, a quickest shipping term and freight will be advised to you for consideration.
3. The stock info will be informed before your order, to make everything under control.
4. Price could be negotiated for more and large quantity.
Shipping & Duties
Usually, shipping will be arranged within 2-3 Days upon payment or deposit, from Monday to Saturday only.
To assure you the maximum comfort and satisfaction, Currently, you can pay via T/T, L/C, WESTERN UNION, PAYPAL or through Visa, MasterCard via Ali Express Escrow. More payment options will be added in the near future.
All of the products we sell are with a certain time warranty, during the warranty, anything wrong with it, we will take care of it.
We will always be here and try our best to provide you our best service !